Set Alert for Product: BIGTREETECH PAD 7 Touch Screen Based on Klipper firmware 7 inch Open Source Smart PAD with CB1 Board KlipperScreen for BIQU B1 SE Plus, Voron 2.4, Ender-3 and Most FDM 3D Printers DIY - $129.99
【Upgrade Printing Speed and Quality】PAD 7 upgrade and pre installed Klipper firmware, using Klipper’s input shaper and BTT ADXL345 module, can effectively improve printing speed while ensuring printing quality, printing speed can be increased by 2 to 5x compared to Marlin firmware; You…
【Upgrade Printing Speed and Quality】PAD 7 upgrade and pre installed Klipper firmware, using Klipper’s input shaper and BTT ADXL345 module, can effectively improve printing speed while ensuring printing quality, printing speed can be increased by 2 to 5x compared to Marlin firmware; You…
Additional information
Specification: BIGTREETECH PAD 7 Touch Screen Based on Klipper firmware
All prices mentioned above are in United States dollar.
This product is available at Amazon.com.
At amazon.com you can purchase BIGTREETECH PAD 7 Touch Screen Based on Klipper firmware 7 inch Open Source Smart PAD with CB1 Board KlipperScreen for BIQU B1 SE Plus, Voron 2.4, Ender-3 and Most FDM 3D Printers DIY for only $129.99
The lowest price of Creality Sonic Pad Based on Klipper Firmware 7 Inch Touch Screen 3D Printer Smart Pad with Higher Printing Speed for Creality Ender 3 Pro/Ender 3 V2/Ender 3 V3 SE/Ender 3 S1 Series Ender 3D Printers was obtained on June 27, 2024 8:38 pm.
Price History for BIGTREETECH PAD 7 Touch Screen Based on Klipper firmware 7 inch Open Source Smart PAD with CB1...
Review of BIGTREETECH Pad 7 Klipper pad with Creality Ender-3 Pro S1 3D printer - CNX Software
May 29, 2023 -
CNX Software
Creality's Sonic Pad Makes Klipper Installation Super Easy - All3DP
January 3, 2023 -
All3DP
Using BTT Pad 7 touchscreen display with Raspberry Pi CM4 - CNX Software
May 21, 2023 -
CNX Software
Reviews (6)
6 reviews for BIGTREETECH PAD 7 Touch Screen Based on Klipper firmware
4.0out of 5
★★★★★
★★★★★
4
★★★★★
1
★★★★★
0
★★★★★
0
★★★★★
1
Write a review
Show allMost HelpfulHighest RatingLowest Rating
★★★★★
Maia –
this is exactly what I needed for my RasPi setup. my partner had gotten me a small phone stand 3D printed to look like a nether portal. I thought it would look so sick as a monitor stand for my RasPi with the purple blocks as the background/screensaver. I needed a monitor that had a width of…
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
CarlosPatricio –
So, i installed the screen without issue. It worked perfect the first few weeks on my BIQU Hurakan. Installed some updates thru Mainsail, and then the display would not respond to any touch. SO i thought i would try it on my PC. Touch worked perfectly without issue. Im not what the deal is on…
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
dreifach –
I have both the BTT Pad 7 and the Creality Sonic Pad, so I will be comparing them against each other. I have also set up a working Klipper instance on a Raspberry Pi.
The Pad 7 is as much stock Klipper as you can get. BTT hasn’t messed with anything here. The Pad itself is running stock…
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Maia –
El producto es excelente y cumple con todos los requisitos de prestaciones al momento de utilizarlo como un hub Klipper.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
Chris –
I used this smart display for my Voron 2.4 3D printer to replace the small non-touch screen it had. It works SO well and I love it! It is super bright and goes to sleep after a while so it doesn’t cause any burn in or anything.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
The meyer family –
The screen it self is fantastic and works flawlessly, but I just wish they included a longer dsi cable as this is too short to do anything other then mount the PI to the back of the screen, but for a voron this is not ideal and you will require at least a 12 inch cable I opted for a 16inch so…
amazon.com
Maia –
this is exactly what I needed for my RasPi setup. my partner had gotten me a small phone stand 3D printed to look like a nether portal. I thought it would look so sick as a monitor stand for my RasPi with the purple blocks as the background/screensaver. I needed a monitor that had a width of…
CarlosPatricio –
So, i installed the screen without issue. It worked perfect the first few weeks on my BIQU Hurakan. Installed some updates thru Mainsail, and then the display would not respond to any touch. SO i thought i would try it on my PC. Touch worked perfectly without issue. Im not what the deal is on…
dreifach –
I have both the BTT Pad 7 and the Creality Sonic Pad, so I will be comparing them against each other. I have also set up a working Klipper instance on a Raspberry Pi.
The Pad 7 is as much stock Klipper as you can get. BTT hasn’t messed with anything here. The Pad itself is running stock…
Maia –
El producto es excelente y cumple con todos los requisitos de prestaciones al momento de utilizarlo como un hub Klipper.
Chris –
I used this smart display for my Voron 2.4 3D printer to replace the small non-touch screen it had. It works SO well and I love it! It is super bright and goes to sleep after a while so it doesn’t cause any burn in or anything.
The meyer family –
The screen it self is fantastic and works flawlessly, but I just wish they included a longer dsi cable as this is too short to do anything other then mount the PI to the back of the screen, but for a voron this is not ideal and you will require at least a 12 inch cable I opted for a 16inch so…